Plumbing for Beginners: What You Need for Installing a Bathtub
Plumbing for Beginners: What You Need for Installing a Bathtub
Blog Article
Listed here in the next paragraph you will find some excellent information with regards to How to Install a Bathtub.
Installing a bathtub isn't precisely rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Changing an old bathtub with a new one is additionally a moderately challenging task. If the old tub is readily easily accessible, the job can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also place the brand-new bathtub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will require an assistant to move out the old tub as well as set in the new one. Make sure you have actually qualified yourself for the job and also fit attempting it. Rather than working with a professional to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly aid you set up a new tub in your shower room if you have already gotten a new tub and don't need to change the setup of your previous water pipes.
Your devices and material checklist must make up the following:
Getting ready for the Installment
To start with, the sustaining structure provided with the bathroom should be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any type of water staying in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted access that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before going on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, put the bath tub in the called for setting. The wood boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bathtub till the spirit level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leakages and also tighten them if needed. Load the bathtub and additionally check the overflow electrical outlet and the normal outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bathtub needs to wait up until the bathtub has been used a minimum of once as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place between the faucet and the sink. Protect the faucet in place with the manufacturer provided backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former kind ought to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall in between the bathroom and the tiling, leading to complications with dampness and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are sold in tubes as well as cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split rather early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily offered on the market. It is suggested to fit the tiles using water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that article about How to Install a Bathtub Yourself from a good friend on our other web address. Sharing is good. Helping others is fun. Thank you so much for your time spent reading it.
Top-notch service? Dial here. Report this page